AminetAminet
Search:
82086 packages online
About
Recent
Browse
Search
Upload
Setup
Services

driver/media/Polled-pbscsi.lha

Mirror:Random
Showing:m68k-amigaosppc-amigaosppc-morphosi386-arosi386-amithlonppc-warpupppc-powerupgeneric
No screenshot available
Short:SCSI driver for A1000 Phoenix boards
Author:Erich.Loew at joanneum.ac.at (Erich Loew)
Uploader:Erich Loew joanneum ac at (Erich Loew), gordonf intouch bc ca (Gordon Fecyk)
Type:driver/media
Version:7.17 (1997-09-16)
Requires:Phoenix MB and KS 2.04 or later
Architecture:m68k-amigaos
Distribution:Aminet
Date:1997-10-12
Download:http://aminet.net/driver/media/Polled-pbscsi.lha - View contents
Readme:http://aminet.net/driver/media/Polled-pbscsi.readme
Downloads:1572
PBSCSI 7.17 is a replacement driver for Phoenix Microtechnologies' SCSI
adapter found on their Phoenix Replacement Motherboards for the Amiga 1000.
It is based on Erich Loew's driver for Otronic's OSSI hardware, which like
the Phoenix MB SCSI, uses AMD's 5380 single-chip SCSI controller.
The driver could be easily adapted to other 5380-based SCSI devices, such as
IVS's Trumpcard, Xetec's FastTrak, etc (Write Erich or me for more
information).

This driver is a non-DMA driver like the original PBSCSI revisions J or
older.  Unlike Rev J, however, this driver makes use of the hardware
interrupt logic implemented on the Phoenix MBs in revisions I or later.  
This allows the SCSI subsystem to work with disconnect/reconnect, diskchange 
interrupts, and provides an overall compatibility improvement with all 
SCSI-II hardware.  
Hard disk performance will not improve significantly, but non-HD devices 
(CD-ROMs notably) will improve dramatically thanks to the improved CPU usage 
and interrupt handling.

For more info on a pseudoDMA driver variants that improves read/write speed 
by 600%, read the Distribution Info on the bottom.


Installation:

This driver is not an EPROM image; you may safely start your system with
your original Revision I or J EPROM.  The only hardware mod you need to
perform is adding a jumper across L30 (located near the hard disk LED
connector near the SCSI connectors).  You may safely install this jumper
and use this driver or your original driver.  

* ADD THIS JUMPER BEFORE CONTINUING!!! *  

If disk performance sucks after you use this driver, it's
because you forgot to install the jumper on L30.


Software install method 1...

 - Disable the autobooting of the ROM resident driver using Jumper L35.

 - Setup a botable WorkBench floppy disk with at least:
 
     + C/BindDrivers
     + Expansion/Phoenix
     + Expansion/Phoenix.info
     + S/Startup-Sequence

 - Make the floppy bootable with the C:Install command

 - The file S/Startup-Sequence should contain the following line:
   C:BindDrivers

 - Boot from this floppy disk

 - Remove the floppy disk

 - Reboot again

 - And now the system autoboots from your hard disk resident boot partition
   until you power off the Amiga.
   

This method works as a normal BindDrivers type driver, with the exception 
that it stays resident between reboots (If you use a boot floppy --- as
stated above --- you only need to use it once).


Software install method 2...

 - Do not disable autobooting from the REV I or J EPROMs!

 - Copy the included "PHOENIX" file to any convenient place on your hard disk,
   and include this line early (before SetPatch) in your startup-sequence:

   (path)/phoenix

 - When the startup-sequence hits this line, the driver will load, hook itself
   into ROMKickTag, and force a reboot.  This reboot will occur with the
   replacement driver active overriding the EPROMs until you power off
   your AMIGA.  
   This is a preferred solution if you have any non-autoconfig memory boards 
   that also hook into ROMKickTag (such as CSA's Derringer '030 D3 command, 
   or other resident AddMem program); load the memory board's AddMem command 
   first (without forcing a reboot), then PHOENIX.
   This allows the driver (and much of the OS) to relocate itself to FAST 
   memory on your non-autoconfig board.

   Example of a typical S:Startup-Sequence file:

   Sys:Utilities/D3 DRAM -res
   Sys:Expansion/PHOENIX
   C:SetPatch < NIL: > NIL: QUIET
   (etc...)

 - Again: The new driver will remain active untill you power off the Amiga!

 - Usage: You may disable the driver without powering off the Amiga with 
   the included KillDriver command, but I doubt you'll want to do this. :-)


32-bit CPU users will want to try setting their FileSystem masks to
0xFFFFFFFC instead of the default 0x00FFFFFE, as this allows the file 
system driver to use 32-bit memory and improve random access speeds.  
The pbscsi 7.13 driver will use FAST memory if available, so if the 
file system also uses 32-bit memory, there's no need to touch CHIP 
memory for any disk access, greatly improving random access 
performance (Directory scans, defragmenting, etc)

A few very ancient SCSI devices (Notably SyQuest's SQ555 and Fujitsu's old
M26xx drives) will sieze up during access if you set the FileSystem mask to
0xFFFFFFFC.  SyQuest drives can be fixed by requesting a firmware upgrade
from SyQuest for free.  Newer SQ drives do not exhibit this problem.  As
for Fujitsu's drives, just try flipping DIP switches, one at a time, until
the siezing stops.  Modern disks do not exhibit this behaviour.


Compatibility:

Tested on OS versions 2.04 through 3.1 (3.1 testing performed on OSSI
hardware, but Phoenix hardware is identical).  Also tested with new NSD
specs and FastFileSystem 43.14 for > 4 GB disk compatibility.  FFS 43.14
available from ftp.amiga.de.


It also work on KS 1.3.

Phoenix's original pbscsi.amhd for A-MAX II still works but this does not
gain any benefits from the interrupt handling or reduced CPU speed.  I 
gather that Shapeshifter will work without special drivers, but I haven't
tried.


Distribution info:

This version is freely distributable but is not Public Domain.  You may not
reverse-engineer/decompile/mangle/etc this code (Contact either of us for
porting to other 5380-based SCSI devices).

There is also a pseudoDMA version of this driver which requires some
hardware patching, but will greatly improve disk performance by nearly 600%
over the original Rev J driver.  The price is $20.00 US for the pseudoDMA
driver, step by step modification guide, and controller tuning guide.  The
hardware patch involves an additional 74HC00 part, trace cutting on the
Phoenix MB, and wire soldering.

Plans are also afoot for an EPROM version of both drivers to completely
replace Rev I or J.  We would also love to consider replacement A-MAX II
or Shapeshifter drivers if anyone out there knows how to write them.
We especially can use assistance regarding the Rev J EPROM layout, as we
need to somehow cram 11KB of code into this thing that only allows us two 8
KB segments.


Contact Infos:

Erich Loew
St. Peter Hauptstrasse 33c/8/17
A 8042 Graz
Austria

Gordon Fecyk
BSMT 5531 McRae Street
Richmond, BC   V6V 2P5
Canada


Contents of driver/media/Polled-pbscsi.lha
 PERMSSN    UID  GID    PACKED    SIZE  RATIO METHOD CRC     STAMP          NAME
---------- ----------- ------- ------- ------ ---------- ------------ -------------
[generic]                  390     621  62.8% -lh5- e6c4 Oct 12  1997 Polled-pbscsi-7.17.info
[generic]                  386     621  62.2% -lh5- bb5a Oct 12  1997 Polled-pbscsi-7.17/Expansion.info
[generic]                 9935   16352  60.8% -lh5- 0525 Oct 12  1997 Polled-pbscsi-7.17/Expansion/PHOENIX
[generic]                  596     988  60.3% -lh5- 09f3 Oct 12  1997 Polled-pbscsi-7.17/Expansion/PHOENIX.info
[generic]                 3167    6699  47.3% -lh5- 04aa Oct 12  1997 Polled-pbscsi-7.17/PhoenixSCSI.readme
[generic]                  276     835  33.1% -lh5- 94d2 Oct 12  1997 Polled-pbscsi-7.17/PhoenixSCSI.readme.info
---------- ----------- ------- ------- ------ ---------- ------------ -------------
 Total         6 files   14750   26116  56.5%            Oct 12  1997

Aminet © 1992-2017 Urban Müller and the Aminet team. Aminet contact address: <aminetaminet net>